Raised-panel steel
Carriage house
Modern flush
Full-view glass
LiftMaster openers
Chamberlain openersFull 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the pro arrives.
Get your free estimateTrusted Garage Door Spring Repair for Boulder Homeowners
A broken garage door spring brings everything to a stop. The door won’t lift, or it drops hard and hangs crooked, and suddenly your car is trapped inside. We handle garage door spring repair in Boulder as a dedicated specialty, not a side job. That means torsion and extension springs, snapped cables, and the adjustment work that keeps a door balanced. Springs store enormous tension. A trained tech with the right winding bars is the only safe way to deal with them, so don’t put your hands near a wound spring. Our technicians have up to 11 years of experience, and we know the brand-specific quirks that show up across Raynor, LiftMaster, Chamberlain, and Genie hardware. Springs fail without warning, so we run same-day service for Boulder calls. Reach us at (855) 694-6347 and we’ll get a technician moving.
What Our Garage Door Spring Repair Service Includes
Springs are the most dangerous part of any garage door system, and they’re also the most frequently botched. We treat every spring job as a safety-sensitive repair, with a balance check and a full cycle test before we consider it done. Here’s what each part of the service covers.
Torsion Spring Replacement
A torsion spring is the coiled spring mounted on the horizontal shaft above the door, and it does the heavy lifting by winding and unwinding as the door travels. When one breaks, you’ll usually hear a loud bang and find the door dead in its tracks. We replace the spring, check the other spring in the pair, and re-tension the system so the door runs balanced. A matched pair is usually replaced together, because springs that were installed at the same time wear out on roughly the same schedule. We’ll tell you honestly whether one spring or both need to go.

Extension Spring Replacement
Extension springs stretch along the tracks on either side of the door and pull it upward. They’re common on older doors and lighter-weight setups. When they break, the door can slam down hard, which is why a safety cable through the center of each spring matters so much. We replace extension springs and confirm the cables and mounting hardware are sound before the door goes back into service.

Broken Spring Repair
Broken spring repair is exactly what it sounds like: getting a snapped spring out and a working one back in so the door opens safely again. If your door won’t budge or feels impossibly heavy when you try to lift it by hand, a broken spring is the usual cause. We diagnose whether it’s a spring, a cable, or something in the opener, then fix the actual problem instead of guessing. It’s the difference between a real fix and a callback in two weeks.

Spring Adjustment
Spring adjustment means setting the tension so the door lifts with a light, even effort and stays put when you let go halfway up. A door that slams down or won’t stay open has lost its balance, and a tired spring or one set too loose is usually to blame. We measure the door’s weight against the spring tension and dial it in, which takes stress off the opener and makes the door quieter and safer to use.
Safety Cable Installation
A safety cable is a steel cable that runs through the middle of an extension spring so that, if the spring ever snaps, the pieces stay contained instead of flying across the garage. Older doors often don’t have them, and some have cables that have rusted or frayed. We fit new safety cables where they’re missing and replace the ones that are past their useful life. It’s a small job that changes what happens on a bad day.
Spring Inspection
A spring inspection is a close look at the springs, cables, drums, and mounting points to catch wear before a spring lets go. We check for gaps in a torsion spring’s coil, stretch in an extension spring, and fraying or rust on the cables. Catching a spring on its way out lets you plan the repair instead of dealing with it in a hurry. A worn-looking spring is worth a call before it fails.
Styles & brands we work with
- Raised-panel steel
- Carriage house
- Modern flush
- Full-view glass
- LiftMaster openers
- Chamberlain openers
Brands We Service for Garage Door Spring Repair
We work on your brand, and that matters when a spring job runs into brand-specific hardware. Raynor systems and older LiftMaster setups have their own winding conventions, drum designs, and mounting details, and knowing where those wear out saves a lot of trial and error. On Chamberlain and Genie doors we know the typical spring and cable pairing and the balance points that keep the door running clean. Diagnosing the right part the first time is most of the job.
Whether you have Raynor, LiftMaster, Chamberlain, Genie, or any other make, we can help. Spring repair is the same physics across brands, but the details differ, and a technician who’s familiar with your door’s hardware gets it right the first time instead of ordering a part that doesn’t fit. From a broken spring to a full new door, we cover the whole range, and we don’t have to pass a spring job off to someone else.
Signs You Need Garage Door Spring Repair Right Now
Springs usually give some warning before they fail, though a torsion spring can snap mid-cycle with no advance notice. Here’s what to watch for.
- A loud bang from the garage. That crack is often a torsion spring letting go all at once. After that, the door won’t open, and forcing it stresses the opener and the rest of the hardware.
- The door feels heavy when you lift it. If a door that used to lift easily now feels like dead weight, a spring has lost tension or broken. Stop lifting it by hand and let a tech check the springs, because the tension is what’s now missing.
- The door drops fast or won’t stay up. A door that slams shut or sags when you let go halfway up is out of balance. That’s an adjustment or replacement issue, and it’s also a safety one.
- The door hangs crooked or one side lifts first. An uneven door usually points to one broken spring in a pair or a stretched extension spring on one side. Running it crooked wears the tracks and rollers.
- Visible gaps, stretch, or rust in the springs. A torsion spring with a visible gap in its coil or an extension spring that’s noticeably longer than its partner is on its way out. Rust and fraying on the cables are worth the same look.
Our Garage Door Spring Repair Process – Step by Step
Spring repair doesn’t leave room for guesswork, so we follow the same sequence on every job. Here’s how a typical service call runs.
- 1
Listen and inspect. We start by asking what the door did and when, then look over the springs, cables, drums, and mounting points. We test the door’s balance by hand to confirm what’s actually wrong before we touch anything.
- 2
Diagnose the failure. We identify the specific part that failed and check whether the other spring in a pair is close to failing too. If the opener or a cable is part of the problem, we say so now instead of after the spring’s replaced.
- 3
Quote before we start. You get a written price for the parts and labor before any work begins. The number we agree to is the number you pay, and if we find something else once the old spring is out, we talk it through with you first.
- 4
Replace and re-tension. We wind down the old spring, fit the new one, and set the tension so the door balances. We check the safety cables and hardware while we’re in there, since a new spring on tired cables isn’t a real fix.
- 5
Test and cycle the door. We run the door through several full open-and-close cycles, check the balance and the opener’s force settings, and make sure it stops and reverses the way it should. You get a door that works, not just a spring that’s been swapped.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Garage Door Spring Repair Cost in Boulder?
Garage door spring repair in Boulder typically runs $180 – $340 for one spring, depending on the spring type and the door’s weight. That’s the range for a single spring. A matched pair is usually replaced together because the springs wear on the same schedule, so a pair costs about twice that range. Extension springs on a lighter door often land at the lower end, while a torsion spring on a heavy insulated door sits toward the top.
Here’s how the common jobs break down:
- Torsion spring replacement: $180 – $340 for one spring, roughly double for a matched pair.
- Extension spring replacement: $180 – $340 for one spring, roughly double for a pair.
- Spring adjustment or inspection: usually at the lower end of the range, since no new spring is involved.
- Safety cable installation: often bundled into an extension spring job.
What moves the price is the spring type, the door’s weight and size, whether one spring or a pair is involved, and whether a cable or drum also needs attention. The way to avoid overpaying is to get a written estimate before work starts and to ask whether a pair makes sense. Our estimates are free and include a look at the whole system, so you know what’s failed and what’s still healthy. The written estimate sets the final price.
Garage Door Spring Repair Near Boulder – Our Service Area
We cover Boulder and the communities around it, including Louisville, Superior, Lafayette, Erie, Broomfield, Longmont, Westminster, Arvada, Frederick, Northglenn, and Dacono. Response is same-day for most calls, and we’ll give you a realistic window when you phone. If you’re outside Boulder, we handle garage door spring repair in the surrounding towns with the same technicians and the same process. Farther out, we’ll confirm timing when you call.
Serving Boulder, CO – Our Local Coverage Area
We serve Boulder and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Garage Door Spring Repair in Boulder
Garage door spring repair is the replacement or adjustment of the springs that counterbalance the door’s weight, so it lifts with light effort and stays put when it’s partway open. It covers torsion springs on the shaft above the door and extension springs along the side tracks, plus the cables and hardware that go with them. It’s a safety-sensitive job because a wound spring holds a lot of stored energy. We do it with the proper winding tools and a balance check so the door works correctly afterward.
Most single-spring repairs take about an hour to an hour and a half on site, and a matched pair runs a bit longer. The timing assumes the right spring is on hand and nothing else is worn out. If a cable or drum is also failing, we’ll tell you before we start so there are no surprises. Call (855) 694-6347 and we’ll give you a realistic window for your door.
Spring repair in Boulder typically runs $180 – $340 for one spring, with a matched pair costing about twice that range. The final number depends on the spring type, the door’s weight, and whether cables or hardware need attention. You’ll get a written price before we start, and the agreed quote is what you pay. Call (855) 694-6347 for an exact quote – estimates are free.
Yes, we service LiftMaster and Chamberlain doors and openers, along with Raynor and Genie systems. Spring repair is the same physics across brands, but the winding hardware and balance points differ, and that’s where brand familiarity pays off. We also work on Clopay, Amarr, Wayne Dalton, and Craftsman equipment. If your door has a brand-specific quirk, we’ve likely seen it.
Yes, we run same-day service for broken springs in Boulder, because a door that won’t open leaves your car stuck and your garage exposed. Call (855) 694-6347 and we’ll give you the earliest realistic window. If you’re calling outside our usual hours, we’ll book you for the next available slot rather than leave you guessing. The same technicians handle emergency calls as scheduled ones.
We’ll confirm the warranty terms for your specific job when we quote it, since it depends on the spring and the work done. Ask before we start and we’ll put it in writing along with the price. The parts and labor are spelled out so you know exactly what’s covered. Call (855) 694-6347 and we can talk through the details.
Clear the area under and around the door and keep vehicles out of the garage if you can so the technician has room to work. Don’t try to lift or cycle the door yourself, since a door with a broken spring can drop hard. It also helps to have the door’s make and any opener brand ready when you call, so we bring the right parts. Then just leave the door closed until we arrive.
Schedule Your Garage Door Spring Repair Service in Boulder Today
A broken spring won’t fix itself, and forcing the door only makes things worse. Call (855) 694-6347 for same-day service in Boulder and a written estimate before any work starts. Our technicians have up to 11 years of experience, and we handle spring repair as a specialty. Free estimates, upfront pricing, and a door that works right the first time.
Written by the team at Boulder Garage Door Repair Pros.